BONFIGLIOLI Active Cube Instructions d'exploitation Page 83
- Page / 176
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
04/08 Application manual Positioning 81
4.5.2 Acceleration and Deceleration in JOG Mode
In JOG mode separate acceleration and deceleration ramps with S curves (ramp
times) are used:
Parameter Setting
No. Description Min. Max. Fact. sett.
1175 Acceleration 1 u/s
2
232-1 u/s
2
327 680 u/s
2
1176 Ramp Rise Time 0 ms 2000 ms 0 ms
1177 Deceleration 1 u/s
2
232-1 u/s
2
327 680 u/s
2
1178 Ramp Fall Time 0 ms 2000 ms 0 ms
1179 Emergency Ramp 1 u/s
2
2
32
-1 u/s
2
655 360 u/s
2
Fixed Speed/
Jog-Speed Keypad
Acce
l
eration
1175
Deceleration
1177
R
am
p
Rise Time
1176
Ramp Fall Time
1178
t
4.6 Teach-In (Saving Actual Position as Target Position)
The "Teach-In" function is used in order to approach the target positions in a plant
manually and to save the corresponding position values in the motion blocks. The
function works like the JOG function, with the following differences:
−
Teach-In is activated via parameter
Operation Mode 1221.
− By default, input MFI1D (Terminal X210B.6) is used for the teach-in signal.
How teach-in works:
− Set the motion block to be parameterized via digital inputs or parameter
Starting-
Record Number
1228.
− Move to required target position in JOG mode.
−
Save actual position for the selected motion block via
Teach-In Signal 1239.
− Repeat procedure for other positions.
−
JOG mode is activated automatically in teach-in mode (parameter
Operation
Mode
1221).
Note: The first two steps of the sequence above can be executed vice versa.
Activate "Teach-In" function:
Set parameter
Operation Mode 1221 to:
− "301 - Teach-In, Motion Block Sel. via Digital Inputs" or
− "302 - Teach-In, Motion Block Sel. via P. 1228"
Application manual Positioning 8104/08
- ACTIVE CUBE 1
- TABLE OF CONTENTS 4
- 1.1 General Information 7
- 1.3 Transport and Storage 8
- 1.5 Electrical Connection 9
- 1.6 Information on Use 9
- 1.7 Maintenance and Service 9
- 2 System description 10
- ACTIVE Cube 11
- 3.5.1 Getting started 20
- 3.5.2 Reference system 23
- Gear Box: Motor sha 24
- 3.5.4 Control via software 27
- Operation 30
- Operation mode 1221 33
- 4.2 Homing 36
- Function 37
- 4.2.3 Homing mode 39
- Home-Offset 40
- Home switch 40
- 4.3 Positioning Mode 41
- 4.3.2 VTable 42
- 4.4.1 Motion Mode 43
- Motion Mode 1208 44
- Motion Mode 45
- Touch-Probe-Error: Next 48
- Motion Block 1210 48
- Motion Mode 1208) 50
- Maximum Frequency 50
- Acceleration 52
- Deceleration 52
- Ramp Rise Time 53
- Delereation Ramp Fall Time 53
- Target Position/Distance 53
- Limitation 54
- 4.4.2 Motion block data 56
- 4.4.2.1 Target position 56
- 4.4.2.2 Speed 56
- Next motion block 62
- Actual Motion Block 1246 63
- Operation Mode 63
- 4.4.2.5 Single motion 64
- 4.4.3 Control of motion 65
- Assign digital input signals 66
- Deceleration 1206. If the 69
- Deceleration 1202. If the 69
- Target Position 70
- Start Positioning 71
- Stop Positioning 71
- Deceleration 1206 72
- Starting-Record Number 1228 73
- Digital Signal 1 1218 75
- Digital Signal 2 1219 75
- Digital Signal 3 1247 75
- Digital Signal 4 1248 75
- Motion Mode 1208: 76
- Speed 1203 is reached 76
- Digital Signal 3 1247 = 12 77
- 4.5 JOG Mode 78
- Jog Anticlockwise 80
- Jog-Mode Active 80
- Jog Clockwise 80
- Jog-Speed Keypad 1174 82
- Operation mode 86
- 4.7 Electronic gear 87
- 4.7.1 Master position source 87
- Master Position Source 88
- Operation Mode 1180 88
- SYNC-Time 88
- Resync. on Change of 89
- Gear Factor 1142 89
- Start Phasing 90
- Phasing: Offset 90
- Phasing: Speed 90
- Phasing: Acceleration 90
- 4.8 Monitoring Functions 92
- 4.8.1 Travel limits 92
- Operation Mode 490 of speed 93
- Pos. HW Limit Switch 1138 = 93
- Assign digital inputs 94
- Hysteresis 1149 95
- Fault Reaction 1143 96
- Fault Reaction 1144 98
- 4.8.4 Target window 101
- Fault Reaction 1120 102
- Peak Value Con 103
- Actual Appl. Warning Mask 105
- Warnings 269 105
- Speed Override 1236 106
- Hysteresis 107
- Off-Position 107
- On-Position 107
- Configuration 30 = 440 only) 108
- Operation mode 1240 109
- Feed Con 110
- Operation Mode 1240: 110
- Configuration 30 = 440 112
- 0.25-0.25 0.00 113
- Latched Position 1281 114
- 4.14 Wiring Example 115
- 440 uses internal operands 116
- 5 List of homing modes 117
- 5.1 Brief Description Homing 117
- Homing Mode 1130 118
- 5.4 Terminology 121
- Homing Mode 122
- Fast Speed 1132. When the 131
- Creep Speed 131
- Creep Speed 1133 131
- Fast Speed 1132 131
- Fast Speed 138
- Home position 139
- Pos. HW Limit Switch 139
- Actual position value 152
- Actual Motion Mode 1255 155
- Statusword 411 156
- 1125. Parameters of phasing 158
- ≤ xx ≤ 32) 162
- Constant 165
- 7 Parameter List 166
- 7.1 Actual Value Menu (VAL) 166
- 7.2 Parameter Menu (PARA) 166
- 168
- 4.2.5 1132 Fast Speed 170
Produits connexes et manuels pour Adaptateurs et onduleurs de puissance BONFIGLIOLI Active Cube
(27 pages)
(74 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.035 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels