BONFIGLIOLI EM-RES-02 Instructions d'exploitation

AND UTOMATION OLUTIONSASIPNDUSTRY ROCESSACTIVE andACTIVE CubeExpansionModule EM-RES-02GBFrequency Inverter 230 V / 400 V

08/06 9 3.3.2 Control Sockets The control and software functionality can be freely configured for economical opera-tion with a safe f

10 08/06 4 Control inputs and outputs 4.1 Analog input EM-S1INA 4.1.1 General The analog input of the EM-RES-02 expansion module

08/06 11 4.1.3 Characteristic The mapping of the analog input signals onto a frequency or percentage reference value is possible for va

12 08/06 4.1.4.1 Examples The analog input signal is mapped onto a reference value as a function of the charac-teristic. The following e

08/06 13 Characteristic point 1: X1 = 30.00 % · 10 V = 3.00 V Y1 = -50.00 % · 50.00 Hz = -25.00 Hz Characteristic point 2: X2 = 80.00 % · 10

14 08/06 Operation mode "101 – bipolar absolute value" The operation mode "101 – bipolar absolute value“ maps the bipolar

08/06 15 4.1.6 Tolerance band and hysteresis The analog input characteristic with change of sign of the reference value can beadapted

16 08/06 4.1.7 Error and warning behavior The monitoring of the analog input signal necessary according to the application is tobe confi

08/06 17 4.1.8 Adjustment As a result of component tolerances, it can be necessary to adjust the analog input. Parameter Adjustment 5

18 08/06 4.2 Resolver input EM-RES The resolver input is used for evaluating the position information from the resolver. The frequenc

08/06 1 General points on the documentation The present supplement of the documentation is valid for the frequency inverter se-ries ACT and

08/06 19 • Set parameter Operation Mode 380 to the frequency value of the field signal forthe resolver. • Adjust parameter No. of Pol

20 08/06 Depending on the behavior of the motor after start, carry out the following steps: − Motor does not turn, or the motor shaft only t

08/06 21 4.2.2 Actual speed source Switch-over is effected via Actual Speed Source 766. If the resolver delivers the actual value sign

22 08/06 4.4 Actual value display The actual value of speed sensor 2 can be read via the parameters Frequency speedsensor 2 219 and Spee

08/06 23 5 Parameter list The parameter list is structured according to the menu branches of the control unit.For better clarity, the pa

24 08/06 6 Annex 6.1 Error messages The various control functions and methods and the hardware of the frequency invertercontain functio

AUSTRALIABONFIGLIOLI TRANSMISSION (Aust) Pty Ltd.48-50 Adderley St. (East) Auburn (Sydney) N.S.W. 2144Tel. (+61) 2 8748 4400 - Fax (+61) 2 9748 8740P.

www.bonfiglioli.comIPNDUSTRY ROCESSAND UTOMATION OLUTIONSASACTIVE andACTIVE CubeCOD. VEC 225 R2

2 08/06 TABLE OF CONTENTS 1 General safety and application information ... 3

08/06 3 1 General safety and application information This documentation has been created with greatest care and has been extensively and

4 08/06 1.3 Transport and storage Transport and storage are to be done appropriate in the original packing. Store theunits only in dry ro

08/06 5 2 Introduction This document describes the possibilities and the properties of the EM-RES-02 expan-sion module for the frequenc

6 08/06 3 Installation of the EM-RES-02 expansion module 3.1 General The mechanical and electrical installation of the EM-RES-02 expansi

08/06 7 The EM-RES-02 expansion module is supplied in a housing for assembly on the lowerslot of the frequency inverter. • Remove th

8 08/06 3.3 Electrical installation Danger! If the following instructions are not complied with, there is direct danger with the possible co